seagate backup plus for mac does it work on pc

#Seagate backup plus for mac does it work on pc pro
#Seagate backup plus for mac does it work on pc Pc
#Seagate backup plus for mac does it work on pc windows

#BC Command Timeout - this one is serious - it's a count of the times the drive has failed to respond to a command because it was busy. As with #1, it might not be a decimal number but it should be zero, or as close to. #7 Seek Error Rate - record of the times the drive has had problems locating a specific area, or sector, of the disk. It should be as close to zero as possible, and in an ideal world, zero. This is a record of the times the drive has had problems reading data from the its discs. This number is usually recorded either in seconds, minutes, or hours, but even if this is milliseconds, then that's over 6400 years of use! If it's reporting in microseconds then it's 6 years, which is still not possible as this drive wasn't released until late 2016! I think it would be fair to say that this drive has been used a LOT. I'm not actually sure it's reporting it correctly. #9 Power on time - this is an impossibly large number.

If you use it long term then it can monitor your drive's SMART data and predict how long it will last for. It's all just a bunch of movies and music so not important enough to go through a data recovery service, but any advice would be greatly appreciated!ĭon't worry about the TEC stuff - that's part of the Disk Checkup software.

#Seagate backup plus for mac does it work on pc Pc

Is that not recommended? Does it matter if the new drive is NAS? I was planning to buy a 6 TB HDD for my pc soon anyway but want to do the cloning and data recovery with it before installing it. I am looking at either a WD 6 TB internal or a Toshiba 6 TB internal (these seem like the more trusted/recommended HDD manufacturer brands here?) that I would like to clone using some HDD 3.5' USB 3.0 enclosure. From what I've read since on this subreddit, it looks like I shouldn't do anything until I can clone it so I'm trying to figure that out right now and I need to order a big enough drive to do so. Seems like I did multiple stupid things and should have come here first before doing anything. I have a 2.5' USB 3.0 SATA enclosure so thinking the SATA connection piece of the Seagate finally completely crapped out, I removed the drive from the case and removed the connector and tried to connect the drive using the enclosure, which didn't work to mount the drive.Īnyway, I think that's all the background to where I am currently with the drive. I think I might have emptied the trash when I got it mounted again and was saving some files, but I can't remember.

#Seagate backup plus for mac does it work on pc windows

The drive is recognized in disk utility but it will not mount and first aid fails, and it now prompts a read error when plugged into my Windows PC. Thinking the problem solved but still cautious, I started transferring some data off it but only some, I had to use my laptop for something else so I ejected and unplugged the drive thinking I could continue the transferring later. Nothing seemed to come from that (I think it failed? can't remember), no ground gained, I plugged it back into my mac and it eventually mounted to my surprise. Recently I accidentally jostled it when I was transferring some files to the drive and it disconnected with an error, the drive wouldn't mount after many tries and restarts (which usually solves the issue if it isn't mounting but shows all other normal signs of life) so I plugged it into my PC (also wasn't mounted) and I unfortunately followed a terrible data recovery site's instructions to use CHKDSK that I now see was likely just trying to damage the drive further so I would pay for their service. The USB cable connection has been finicky for far too long, often it wouldn't mount unless I got the cable in the right position.

#Seagate backup plus for mac does it work on pc pro

I mainly use the drive on a macbook pro but I used Paragon so I can use it on a Windows PC as well.